We were running out of stack for micropython, and the core1 code doesn't
need 4k. So shift the allocation so that micropython has 6k and core1
has 2k. Adjust the linker script since it didn't support splitting
SCRATCH_X between the two stacks.
Signed-off-by: Matthias Blankertz <matthias@blankertz.org>
Integrate btree extmod in rp2 CMakeLists so it can be enabeled with
MICROPY_PY_BTREE=On.
Default values for DEFPSIZE and MINCACHE copied from esp8266 board.
Note: To be able to use the btree module, you must set the
MICROPY_C_HEAP_SIZE CMake option to at least 8192.
Avoids the new Wunterminated-string-literal when compiled with gcc 15.1.
It would be preferable to just disable this warning, but Clang
-Wunknown-warning-option kicks in even when disabling warnings so this
becomes fiddly to apply.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Avoids the new Wunterminated-string-literal when compiled with gcc 15.1.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Avoids the new Wunterminated-string-literal when compiled with gcc 15.1.
Also split out the duplicate string to a top-level array (probably the
duplicate string literal was interned, so unlikely to have any impact.)
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This brings in:
- requests: do not leak header modifications when calling request
- mip: allow relative URLs in package.json
- mip: make mip.install() skip /rom*/lib directories
- umqtt.simple: restore legacy ssl/ssl_params arguments
- nrf24l01: increase startup delay
- nrf24l01: properly handle timeout
- nrf24l01: optimize status reading
- lora-sx126x: fix invert_iq_rx / invert_iq_tx behaviour
- unix-ffi/json: accept both str and bytes as arg for json.loads()
- unix-ffi/machine: use libc if librt is not present
- requests: use the host in the redirect url, not the one in headers
- aiohttp: fix header case sensitivity
- aiohttp: allow headers to be passed to a WebSocketClient
- usb-device-cdc: optimise writing small data so it doesn't require alloc
- inspect: fix isgenerator logic
- inspect: implement iscoroutinefunction and iscoroutine
Signed-off-by: Damien George <damien@micropython.org>
Otherwise, when compiling on 16-bit systems (where `mp_uint_t` is 16 bits
wide) the compiler warns about "left shift count >= width of type", from
the static inline functions that have RV32_ENCODE_TYPE_xxx macros which
do a lot of bit shifting.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this fix the following would fail:
$ make build-TEENSY40/flexram_config.s
because it didn't create the build directory before generating the file.
Also, make `hal/resethandler_MIMXRT10xx.S` have an explicit dependency on
`flexram_config.s` rather than the latter just being forced to be built
before everything else.
Signed-off-by: Damien George <damien@micropython.org>
There are some newer PYBD_SF6 being produced which have a larger flash,
namely two of 8MiB (instead of the older ones with two of 2MiB).
This commit adds support for these boards. The idea is to have the same
PYBD_SF6 firmware run on both old and new boards. That means autodetecting
the flash at start-up and configuring all the relevant SPI/QSPI parameters,
including for ROMFS and mboot.
Signed-off-by: Damien George <damien@micropython.org>
Allows `MICROPY_HW_QSPIFLASH_SIZE_BITS_LOG2` and
`MICROPY_HW_QSPI_MPU_REGION_SIZE` to be arbitrary expressions, eg function
calls.
The `storage.h` header needs to be included in case access to `spi_bdev_t`
is needed by the macros.
Signed-off-by: Damien George <damien@micropython.org>
Options for a board to configure ROMFS are:
- Leave ROMFS disabled, do nothing.
- Enable by defining `MICROPY_HW_ROMFS_ENABLE_PARTx` to 1 and then in the
linker script define `_micropy_hw_romfs_partX_start` and
`_micropy_hw_romfs_partX_size`.
- Enable by defining `MICROPY_HW_ROMFS_ENABLE_PARTx` to 1 and also define
`MICROPY_HW_ROMFS_PARTx_START` and `MICROPY_HW_ROMFS_PARTx_SIZE` which
can be arbitrary expressions (not necessarily static)
Signed-off-by: Damien George <damien@micropython.org>
This commit allows the user of this driver to intercept the SPI flash
initialisation routine and possibly take some action based on the JEDEC id,
for example change the `mp_spiflash_t::chip_params` element.
To do this, enable `MICROPY_HW_SPIFLASH_DETECT_DEVICE` and define a
function called `mp_spiflash_detect()`.
Signed-off-by: Damien George <damien@micropython.org>
This commit allows the user of this driver to dynamically configure the SPI
flash chip parameters. For this, enable `MICROPY_HW_SPIFLASH_CHIP_PARAMS`
and then set the `mp_spiflash_t::chip_params` element to point to a valid
`mp_spiflash_chip_params_t` struct.
Signed-off-by: Damien George <damien@micropython.org>
To match the instruction length, so the DFS is restored to the XIP value
after an erase or write (due to the final wait WIP).
Signed-off-by: Damien George <damien@micropython.org>
Now raises an exception if the pin doesn't support the alternate function
unit number and line type, eg UART0_TX (previously it only checked the
peripheral).
Signed-off-by: Damien George <damien@micropython.org>
